How to Repair a DEEP SCRATCH in Car Paint (DIY)

00:27:43
https://www.youtube.com/watch?v=Zl_iSYYGBiY

Ringkasan

TLDRDans cette vidéo, Chris Fix explique comment réparer une rayure profonde sur la peinture d'une voiture en utilisant un stylo de retouche. Il détaille un processus en quatre étapes : nettoyage de la zone, préparation de la rayure, application de la peinture et polissage final. Bien que le résultat ne soit pas parfait, il permet d'obtenir une finition satisfaisante à un coût bien inférieur à celui d'une réparation professionnelle. Chris fournit également des conseils sur les outils nécessaires et sur la façon de choisir la bonne peinture pour votre véhicule.

Takeaways

  • 🛠️ Utilisez un stylo de retouche pour des réparations économiques.
  • 🧼 Nettoyez la zone avant de commencer.
  • 🔧 Préparez la rayure en éliminant la rouille et en lissant les bords.
  • 🎨 Appliquez plusieurs couches de peinture pour de meilleurs résultats.
  • ✨ Polissez la zone réparée pour un fini lisse.

Garis waktu

  • 00:00:00 - 00:05:00

    Chris Fix présente une méthode pour réparer une rayure profonde sur la peinture d'une voiture, en utilisant un stylo de peinture automobile. Il souligne que bien que cette méthode ne donnera pas des résultats parfaits, elle est beaucoup moins coûteuse qu'une réparation professionnelle, qui peut coûter jusqu'à 775 dollars. Il explique que le but est d'obtenir un résultat acceptable à distance, où la rayure ne sera pas visible.

  • 00:05:00 - 00:10:00

    Il décrit les quatre étapes essentielles pour réparer la rayure : nettoyer la zone, préparer la rayure en enlevant la rouille et en ponçant légèrement, appliquer la peinture avec le stylo, et enfin, mélanger la nouvelle peinture avec la peinture d'origine. Il fournit également une liste des outils nécessaires pour effectuer la réparation.

  • 00:10:00 - 00:15:00

    Avant d'acheter un stylo de retouche, il est important de s'assurer qu'il contient la bonne couleur de base et un vernis automobile. Chris explique comment trouver le code de peinture de la voiture et mentionne que les stylos de peinture d'origine et de rechange sont souvent identiques, donc le choix peut se faire sur le prix.

  • 00:15:00 - 00:20:00

    Il aborde la question de la décoloration de la peinture due au soleil et comment vérifier si la peinture de la voiture est décolorée. Il montre des exemples de zones protégées et exposées au soleil pour illustrer la différence de couleur.

  • 00:20:00 - 00:27:43

    Chris explique les différentes couches de peinture sur une voiture et comment identifier une rayure profonde par rapport à une rayure de vernis. Il donne des conseils sur la façon de préparer la rayure pour la réparation, en insistant sur l'importance d'éliminer toute rouille et de lisser les bords de la rayure pour un meilleur résultat.

Tampilkan lebih banyak

Peta Pikiran

Video Tanya Jawab

  • Quel est le coût d'une réparation professionnelle pour une rayure profonde ?

    Le coût pour réparer correctement une rayure profonde dans un atelier de carrosserie peut atteindre 775 dollars.

  • Quels outils sont nécessaires pour réparer une rayure profonde ?

    Vous aurez besoin d'alcool isopropylique, d'eau savonneuse, d'un rasoir, de papier de verre, d'un stylo de retouche, et de polish.

  • Comment savoir si la peinture de ma voiture est décolorée ?

    Vous pouvez comparer la peinture derrière la plaque d'immatriculation ou le couvercle du réservoir de carburant avec la peinture exposée au soleil.

  • Combien de couches de peinture devrais-je appliquer ?

    Il est recommandé d'appliquer plusieurs couches de peinture, en veillant à ce qu'elles soient plus épaisses que la peinture d'origine.

  • Puis-je appliquer une cire ou un revêtement céramique après la réparation ?

    Non, il est conseillé d'attendre jusqu'à 30 jours pour que la peinture durcisse complètement avant d'appliquer une cire ou un revêtement.

Lihat lebih banyak ringkasan video

Dapatkan akses instan ke ringkasan video YouTube gratis yang didukung oleh AI!
Teks
en
Gulir Otomatis:
  • 00:00:00
    hey guys chris fix here and today i'm
  • 00:00:02
    going to show you how to repair a deep
  • 00:00:04
    scratch in your car's paintwork you can
  • 00:00:06
    see right here we have a really deep
  • 00:00:08
    scratch that goes across the entire
  • 00:00:10
    fender which was from somebody who keyed
  • 00:00:12
    the car they vandalized it now if you
  • 00:00:14
    have a deep scratch cause somebody keyed
  • 00:00:16
    the car because a shopping cart hit it
  • 00:00:17
    because you scraped up against something
  • 00:00:19
    or somebody scraped up against you
  • 00:00:21
    whatever the deep scratch was caused by
  • 00:00:23
    i'm gonna show you how to repair it
  • 00:00:25
    inexpensively using one of these
  • 00:00:27
    automotive paint pens now a paint pen
  • 00:00:29
    like this is around 15 to 20 dollars and
  • 00:00:31
    i want you to keep that in mind because
  • 00:00:33
    this isn't gonna get you a hundred
  • 00:00:34
    percent perfect results it's not going
  • 00:00:36
    to be like if they re-sprayed the panel
  • 00:00:38
    the best way to repair this would be to
  • 00:00:39
    sand the entire panel down to remove the
  • 00:00:41
    scratch and then respray and feather and
  • 00:00:44
    blend your paintwork into the adjacent
  • 00:00:46
    panels now doing all that paint work
  • 00:00:47
    comes at a cost i actually went out and
  • 00:00:49
    got a quote just to see how much it
  • 00:00:51
    would cost to fix this panel only this
  • 00:00:53
    panel with this scratch and the total
  • 00:00:55
    cost would be
  • 00:00:57
    775 dollars to do this properly at a
  • 00:01:00
    body shop now depending on what car you
  • 00:01:02
    drive in your situation you might not
  • 00:01:03
    want to spend all that money to make
  • 00:01:05
    this a perfect repair so instead i'm
  • 00:01:07
    going to show you how to repair it at
  • 00:01:09
    home using one of these paint pens and
  • 00:01:11
    get results that are good enough get
  • 00:01:13
    results that are they're pretty good
  • 00:01:14
    like you're gonna stand from right about
  • 00:01:15
    here two three feet away and you're not
  • 00:01:17
    gonna notice that this is damaged the
  • 00:01:19
    only way to notice its damage is if you
  • 00:01:21
    get up close or you catch it in a
  • 00:01:22
    certain light and you look for that
  • 00:01:24
    scratch otherwise if you stand back here
  • 00:01:26
    you wouldn't even be able to tell wonder
  • 00:01:28
    what let me show you here's the panel
  • 00:01:30
    right now before we repair it you could
  • 00:01:32
    easily see the deep large scratch and
  • 00:01:34
    here's the same panel after we repair it
  • 00:01:36
    with the touch-up paint the scratch is
  • 00:01:38
    gone and the panel looks great so i
  • 00:01:40
    think that gives you a really good idea
  • 00:01:41
    of the results you can expect after
  • 00:01:43
    you're done watching this video and
  • 00:01:44
    trying it for yourself using the tips
  • 00:01:46
    and tricks i show you this is gonna go
  • 00:01:48
    above and beyond everything you've seen
  • 00:01:50
    i'm gonna show you stuff on how to get
  • 00:01:52
    this basically to disappear and we're
  • 00:01:54
    going to be doing that with four simple
  • 00:01:55
    steps first we need to clean the entire
  • 00:01:57
    panel to remove any dirt and oils so we
  • 00:02:00
    don't contaminate the scratch the second
  • 00:02:02
    step is to prep the deep scratch by
  • 00:02:04
    removing any and all rust and lightly
  • 00:02:06
    sanding the scratch to get it ready for
  • 00:02:08
    the next step the third step which is
  • 00:02:10
    our paint step this is where we're gonna
  • 00:02:11
    use a simple touch-up pen to fill the
  • 00:02:13
    scratch with paint and add a layer of
  • 00:02:15
    clear coat and finally the fourth step
  • 00:02:18
    is the blending step this is where we're
  • 00:02:19
    gonna use some sandpaper and polish to
  • 00:02:21
    blend our new touch-up paint into the
  • 00:02:23
    original paintwork that way it doesn't
  • 00:02:25
    stand out as much and it'll be a lot
  • 00:02:27
    harder to see that this was ever touched
  • 00:02:29
    up so if you follow those four simple
  • 00:02:31
    steps you could do this at home yourself
  • 00:02:33
    and get great results now here are all
  • 00:02:36
    the tools and products you're gonna need
  • 00:02:38
    again trying to keep it simple and
  • 00:02:39
    inexpensive you're gonna need some
  • 00:02:41
    isopropyl alcohol in this case 70 or
  • 00:02:44
    greater you're going to need some soapy
  • 00:02:46
    water this is just dish soap and water
  • 00:02:48
    and you're going to need a razor blade
  • 00:02:50
    like this along with some tape it's a
  • 00:02:52
    good idea to have a couple of microfiber
  • 00:02:54
    towels on hand you're going to need a
  • 00:02:56
    kitchen sponge 2 000 3000 and then 5000
  • 00:03:00
    grit sandpaper and then to finish it off
  • 00:03:02
    some polish and a polishing pad and then
  • 00:03:05
    finally you're gonna need one of these
  • 00:03:07
    paint pens that matches the paint to
  • 00:03:09
    your car now all these tools and
  • 00:03:10
    products i will link in the description
  • 00:03:13
    below so you can easily find each one
  • 00:03:16
    now real quick before you go out and
  • 00:03:17
    purchase an automotive touch-up paint
  • 00:03:19
    pen like this you want to make sure it
  • 00:03:21
    has a couple of features the first thing
  • 00:03:22
    is obviously you want to make sure that
  • 00:03:24
    it has the base coat the color coat that
  • 00:03:27
    you're looking for so we have our white
  • 00:03:29
    right there the next thing very
  • 00:03:31
    important you want to make sure that you
  • 00:03:33
    have automotive clear coat so if we take
  • 00:03:35
    this off right here the bottom part has
  • 00:03:37
    our automotive clear coat and that is
  • 00:03:40
    important because that's going to get us
  • 00:03:41
    those really good results and then
  • 00:03:43
    another feature this pen has is the tip
  • 00:03:45
    right here is good for sanding it gets
  • 00:03:47
    the rust out of the deep scratches and
  • 00:03:49
    then one last thing it's very important
  • 00:03:51
    if we take a look over here at the front
  • 00:03:52
    it shows you the different paint codes
  • 00:03:54
    that this paint pen covers it's bright
  • 00:03:56
    white and we need to make sure this
  • 00:03:58
    matches our paint code for our car so
  • 00:04:00
    how do you find the paint code for your
  • 00:04:02
    car well it's simple to find the paint
  • 00:04:04
    code for your car all you need to do is
  • 00:04:06
    come to the driver's side door open it
  • 00:04:08
    up and you're going to look at the door
  • 00:04:10
    jam stickers located right here and if
  • 00:04:12
    we take a look at this sticker you can
  • 00:04:14
    see it says paint pw7 so pw7 is our
  • 00:04:18
    paint code now let's just say for
  • 00:04:19
    whatever reason you can't find that
  • 00:04:21
    paint code well on this door jam sticker
  • 00:04:23
    is always going to be a vin the vehicle
  • 00:04:25
    identification number which is right
  • 00:04:27
    there all you need to do is write that
  • 00:04:28
    down and then call up the car's
  • 00:04:30
    manufacturer in this case it's a
  • 00:04:31
    chrysler you'd call them up and they
  • 00:04:32
    could give you the paint code just from
  • 00:04:34
    the vin so it's pretty simple to make
  • 00:04:36
    sure you have the correct paint code
  • 00:04:38
    another thing that you might run into as
  • 00:04:39
    you're buying these paint pens is should
  • 00:04:41
    you go after market or should you go oem
  • 00:04:44
    but i'm here to tell you just get
  • 00:04:45
    whichever one's cheaper you can see the
  • 00:04:46
    paint pens look identical that's because
  • 00:04:48
    the aftermarket actually makes the oem
  • 00:04:50
    paint so whichever one you could buy
  • 00:04:52
    that's cheaper go for because they're
  • 00:04:54
    both the same now one last thing you
  • 00:04:56
    should check is for paint fade
  • 00:04:58
    especially if you have an older car over
  • 00:04:59
    time the paint on your car is gonna fade
  • 00:05:02
    because the sun is always beating down
  • 00:05:04
    on it and although you might think your
  • 00:05:06
    paint work looks good it's not faded
  • 00:05:08
    over time it will fade no matter what so
  • 00:05:10
    to check that find something such as
  • 00:05:11
    your license plate which doesn't move
  • 00:05:13
    this is what you've had on there since
  • 00:05:14
    the car was bought and if we remove the
  • 00:05:16
    plate you could clearly see there is a
  • 00:05:18
    difference between the paint that's been
  • 00:05:20
    protected and the paint that's been
  • 00:05:21
    exposed to the sun which is faded
  • 00:05:23
    another place you could check is behind
  • 00:05:25
    the fuel filler door because again this
  • 00:05:27
    paintwork back here isn't touched by the
  • 00:05:29
    sun the sun isn't beating down on it
  • 00:05:31
    because it's protected but you could
  • 00:05:32
    compare it directly to the paintwork
  • 00:05:34
    right next to it and you can see if your
  • 00:05:36
    paintwork is faded in this case it
  • 00:05:38
    doesn't look too bad but you could see a
  • 00:05:39
    slight difference
  • 00:05:41
    and the last example i want to give you
  • 00:05:42
    guys is this right here because it's so
  • 00:05:44
    drastic so for whatever reason the
  • 00:05:46
    taillight bezels on these sn95 mustangs
  • 00:05:49
    fade a lot quicker than the rest of the
  • 00:05:51
    paintwork on the car and this gives you
  • 00:05:53
    a clear depiction of what faded paint
  • 00:05:55
    looks like look at the difference there
  • 00:05:57
    that's huge now it is better to have
  • 00:06:00
    touch-up paint on the car than a big
  • 00:06:02
    black gash or a white gash or whatever
  • 00:06:03
    color is underneath here i'm just
  • 00:06:05
    letting you guys know if you have faded
  • 00:06:07
    paint you're gonna see more of a color
  • 00:06:09
    difference between your touch-up paint
  • 00:06:10
    and your original paint so just keep
  • 00:06:11
    that in mind now in this case our car is
  • 00:06:14
    less than five years old so we really
  • 00:06:16
    don't have to worry about faded paint so
  • 00:06:18
    we could begin our repair of our deep
  • 00:06:20
    scratch now i think it's very important
  • 00:06:23
    to understand the different layers of
  • 00:06:25
    paint that way you know exactly what
  • 00:06:27
    we're doing to repair this so let me
  • 00:06:29
    show you first you have the actual panel
  • 00:06:31
    usually it's sheet metal or plastic then
  • 00:06:33
    the first coat is a primer coat usually
  • 00:06:36
    this is a gray primer and it ranges
  • 00:06:38
    anywhere between 10 and 40 microns thick
  • 00:06:40
    then on top of that primer is a base
  • 00:06:42
    coat this is what gives your car a color
  • 00:06:44
    this color coat is usually within 10 to
  • 00:06:46
    40 microns thick as well and then
  • 00:06:48
    finally on top of that is the thickest
  • 00:06:49
    layer the clear coat layer and that
  • 00:06:51
    protects the base coat and gives it a
  • 00:06:53
    nice glossy shine this could be anywhere
  • 00:06:55
    from 40 microns to 100 microns so in
  • 00:06:57
    total the paint could be anywhere from
  • 00:06:59
    60 to 180 microns and that varies a lot
  • 00:07:01
    because different manufacturers spray on
  • 00:07:03
    different thicknesses of paint and just
  • 00:07:05
    to put that into perspective a plain
  • 00:07:06
    sheet of printer paper like this is
  • 00:07:08
    about 100 microns thick so this is about
  • 00:07:10
    how thick your paintwork is on top of
  • 00:07:12
    your panel so this right here is
  • 00:07:14
    definitely a deep scratch it goes
  • 00:07:16
    through the base coat into the primer
  • 00:07:18
    it's not a clear coat scratch now if you
  • 00:07:20
    do have a clear coat scratch like this
  • 00:07:21
    one right here on my truck don't worry
  • 00:07:24
    this is super easy to repair and i have
  • 00:07:26
    a full in-depth video that shows you how
  • 00:07:28
    to remove a clear coat scratch and i'll
  • 00:07:30
    be sure to link that video in the
  • 00:07:32
    description so you can easily find it
  • 00:07:33
    but to verify this is actually a scratch
  • 00:07:36
    that's in the clear coat only it's not a
  • 00:07:37
    deep scratch or a paint transfer all you
  • 00:07:39
    need to do is get some alcohol on a rag
  • 00:07:42
    and then wipe it down and it should
  • 00:07:44
    disappear like that and this is only
  • 00:07:46
    temporary but you can see how it
  • 00:07:47
    disappears and after a couple seconds
  • 00:07:49
    the alcohol starts to evaporate and the
  • 00:07:51
    scratch will start to be visible again
  • 00:07:53
    but that's a good way to tell if you
  • 00:07:54
    have a clear coat scratch alright so now
  • 00:07:56
    you know the different layers of paint
  • 00:07:57
    the different types of scratches let me
  • 00:07:59
    show you how to repair a deep scratch
  • 00:08:01
    like this and remember the larger the
  • 00:08:03
    deep scratch the harder the repair if
  • 00:08:04
    you have a smaller one it's going to be
  • 00:08:06
    super easy so after you see how we get
  • 00:08:08
    this done you'll be able to do yours no
  • 00:08:10
    problem at all so the first step is to
  • 00:08:12
    clean our entire panel we'll start off
  • 00:08:14
    using soapy water all this is is a
  • 00:08:16
    squirt of dish soap and fill the rest up
  • 00:08:18
    with warm water and just spray this down
  • 00:08:21
    and what this is going to do is this is
  • 00:08:22
    going to remove oils waxes dirt and
  • 00:08:24
    debris stuff like that that we don't
  • 00:08:26
    want to get into our scratch all right
  • 00:08:28
    so step number one is done our panel is
  • 00:08:30
    clean so now we can move on to step
  • 00:08:32
    number two and that is to prep our
  • 00:08:34
    scratch now it's very very important we
  • 00:08:36
    cannot have any rust at all in our
  • 00:08:39
    scratch if there's any rust and you
  • 00:08:41
    paint over that rust the paint will
  • 00:08:43
    bubble so you have to remove all the
  • 00:08:44
    rust luckily we don't have any rust in
  • 00:08:46
    this scratch but let's just say you did
  • 00:08:48
    have some rust just get some 400 grit
  • 00:08:50
    sandpaper fold it over and get that rust
  • 00:08:52
    out of the scratch you could also use
  • 00:08:54
    that abrasive tip on the paint pen this
  • 00:08:56
    is really good at removing rust as well
  • 00:08:58
    you just want to get in that scratch and
  • 00:09:00
    again remove all the rust if there is
  • 00:09:02
    any so once all the rust is removed from
  • 00:09:04
    the scratch the next thing in this step
  • 00:09:06
    to prep the scratch is to remove the
  • 00:09:09
    sharp edges so whenever there's a deep
  • 00:09:11
    scratch the edge of the scratch is steep
  • 00:09:13
    and jagged so we want to sand that edge
  • 00:09:15
    of the scratch to round it out and make
  • 00:09:17
    it less of a steep cliff and more of a
  • 00:09:20
    smooth round hill this will make the
  • 00:09:21
    touch-up paint blend in much better to
  • 00:09:23
    the surrounding paintwork and make it a
  • 00:09:25
    lot harder to see the repair and if you
  • 00:09:27
    take a look at our scratch you could
  • 00:09:28
    clearly see those sharp jagged edges
  • 00:09:30
    that we need to smooth out to make our
  • 00:09:32
    touch-up blend better so start by using
  • 00:09:34
    the abrasive tip on the touch-up pen and
  • 00:09:36
    focus your sanding on the jagged edges
  • 00:09:38
    don't worry if you send a little bit
  • 00:09:39
    onto the clear coat because we're going
  • 00:09:40
    to be adding more later just focus on
  • 00:09:42
    getting those sharp jagged edges nice
  • 00:09:45
    and smooth then wipe down the scratch
  • 00:09:47
    with some alcohol to remove all the dust
  • 00:09:48
    you just created so we could get an
  • 00:09:49
    accurate look at the progress we've made
  • 00:09:52
    so now that the edges are sanded we want
  • 00:09:54
    to feather out our sanding onto the base
  • 00:09:55
    coat and onto the clear coat right next
  • 00:09:57
    to the scratch this is going to give us
  • 00:09:59
    a nice smooth transition and to do that
  • 00:10:01
    you could either use 800 grit or 1000
  • 00:10:03
    grit sandpaper and have a little trick i
  • 00:10:05
    want to show you with the sandpaper if
  • 00:10:06
    we just fold the sandpaper over once
  • 00:10:08
    that's going to give us a sharp edge
  • 00:10:10
    like that and that's not going to help
  • 00:10:11
    us smooth this out this is just going to
  • 00:10:13
    dig into the paint and not give us that
  • 00:10:15
    smooth hill that we need so what we're
  • 00:10:17
    going to do is fold it over one more
  • 00:10:19
    time but don't crease it just lightly
  • 00:10:21
    fold it over so it has like a
  • 00:10:22
    semi-circle there and you can see how we
  • 00:10:24
    don't have a sharp edge that's a nice
  • 00:10:26
    rounded edge and we're going to use that
  • 00:10:27
    to sand our scratch and just look at how
  • 00:10:29
    nicely that rounded sandpaper fits in
  • 00:10:32
    that scratch now to round it out that is
  • 00:10:34
    beautiful that's exactly what you want
  • 00:10:37
    now you're probably wondering how do you
  • 00:10:38
    know when you're done sanding you don't
  • 00:10:39
    want to remove too much well all you
  • 00:10:41
    need to do is feel with your fingernail
  • 00:10:43
    if you could grab the edge of the
  • 00:10:44
    scratch with your fingernail you should
  • 00:10:46
    sand a little bit more to make it more
  • 00:10:47
    rounded in this case this feels nice and
  • 00:10:50
    smooth again it's like a hill rather
  • 00:10:52
    than a cliff i cannot grab this with my
  • 00:10:54
    fingernail so we are done so here's what
  • 00:10:56
    the scratch looked like before with
  • 00:10:57
    sharp jagged edges and here's what it
  • 00:10:59
    looks like after nice and smooth so
  • 00:11:02
    that's all there is to our second step
  • 00:11:04
    remove any rust from the scratch and
  • 00:11:07
    then smooth it out to remove all the
  • 00:11:08
    sharp jagged edges now remember the
  • 00:11:11
    smaller the scratch the quicker and
  • 00:11:12
    easier this is i just did that one
  • 00:11:15
    section right there i still need to do
  • 00:11:17
    the rest of the scratch which is pretty
  • 00:11:19
    big it goes all the way around so i'm
  • 00:11:22
    gonna go knock this out real quick and
  • 00:11:23
    then we can move on to the next step
  • 00:11:24
    which is our painting step now although
  • 00:11:27
    i said i'm going to knock this out real
  • 00:11:28
    quick you want to take your time here
  • 00:11:29
    this is very important to do properly
  • 00:11:32
    sand that scratch down remove any of
  • 00:11:34
    those sharp jagged edges and that's
  • 00:11:36
    going to give you the best results once
  • 00:11:37
    we add our paint with a touch-up pen now
  • 00:11:39
    you can see right here this scratch is a
  • 00:11:41
    lot more narrow it's still a deep
  • 00:11:42
    scratch it still goes all the way
  • 00:11:44
    through the base coat into the primer
  • 00:11:46
    but they use the sharp end of the key
  • 00:11:47
    instead of the wide end so they created
  • 00:11:49
    a narrow deep scratch since your scratch
  • 00:11:52
    might look like this rather than a wide
  • 00:11:53
    scratch that i just showed you here's
  • 00:11:55
    how to prep this one the process is
  • 00:11:57
    basically the same you're going to start
  • 00:11:58
    out with your abrasive tip on the paint
  • 00:12:00
    pen just like before but now the scratch
  • 00:12:02
    is so narrow we're actually setting down
  • 00:12:04
    both edges at the same time and for a
  • 00:12:06
    tight scratch like this we don't want to
  • 00:12:07
    make it too much wider if we could help
  • 00:12:09
    it so keep that sanding right on top of
  • 00:12:10
    the scratch same with the sandpaper keep
  • 00:12:12
    the sandpaper rolled nice and tight that
  • 00:12:14
    way we're focusing just on the scratch
  • 00:12:16
    and don't sand too far off the sides of
  • 00:12:18
    the scratch now here's a really good
  • 00:12:20
    angle to show you how tight we're
  • 00:12:21
    keeping this for sanding the narrow
  • 00:12:23
    scratch and if you take a look even on
  • 00:12:24
    this narrow scratch we made sure we have
  • 00:12:26
    a nice smooth transition and it's not a
  • 00:12:29
    sharp cliff so the same process applies
  • 00:12:31
    we didn't have to make it extra wide but
  • 00:12:33
    we did want to make sure you could see
  • 00:12:35
    there is the primer you can see the base
  • 00:12:37
    coat right there and then the clear coat
  • 00:12:38
    right there so we have multiple layers
  • 00:12:40
    that way when we fill this in we could
  • 00:12:42
    fill it in and hide the scratch now
  • 00:12:45
    after you're done sanding down your
  • 00:12:46
    entire scratch and smoothing it out make
  • 00:12:48
    sure you go back one more time and check
  • 00:12:51
    for any sharp edges and i keep bringing
  • 00:12:53
    this up because it's probably the most
  • 00:12:54
    important part of this entire touch-up
  • 00:12:56
    job to get the best results you should
  • 00:12:58
    not be able to feel a difference between
  • 00:13:00
    the clear coat and the base coat down
  • 00:13:02
    into the primer this should feel nice
  • 00:13:04
    and smooth and it does if there is a lip
  • 00:13:07
    right here i promise you you will see it
  • 00:13:09
    once you add your touch-up paint so with
  • 00:13:11
    our entire scratch nice and smooth you
  • 00:13:14
    can't grab it with your fingernail we
  • 00:13:16
    are done with the prep step and we are
  • 00:13:18
    ready for step number three the painting
  • 00:13:20
    step so we smoothed out the deep scratch
  • 00:13:23
    and now we need to add our touch-up
  • 00:13:24
    paint when we add the touch-up paint
  • 00:13:26
    don't worry about adding too much we
  • 00:13:27
    actually want to overflow out of the
  • 00:13:29
    scratch and be higher than the
  • 00:13:30
    surrounding factory paint so let's go do
  • 00:13:33
    that before you paint make sure you get
  • 00:13:35
    some isopropyl alcohol and a towel and
  • 00:13:38
    wipe down the entire scratch make sure
  • 00:13:40
    you get in the scratch on the edge of
  • 00:13:42
    the scratch and the surrounding area of
  • 00:13:44
    the scratch this is going to remove all
  • 00:13:46
    of those oils waxes grease any dirt any
  • 00:13:50
    dust we want this surface to be
  • 00:13:51
    perfectly clean so that our paint could
  • 00:13:53
    adhere to it now with that completely
  • 00:13:55
    clean the next step is to grab some tape
  • 00:13:58
    and we need to tape off our scratch
  • 00:14:00
    let's start on the bottom of the scratch
  • 00:14:02
    and place the tape about one to two
  • 00:14:03
    millimeters from the edge of the scratch
  • 00:14:05
    it doesn't have to be perfect just make
  • 00:14:07
    sure it's not touching the scratch and
  • 00:14:08
    the reason i suggest taping it it's
  • 00:14:10
    easier for cleanup so with the scratch
  • 00:14:12
    surrounded by tape we don't have to
  • 00:14:13
    worry about touch-up paint getting on
  • 00:14:14
    the surrounding paintwork which adds
  • 00:14:16
    more work for us later on so when we're
  • 00:14:18
    done clean up is easy just remove the
  • 00:14:20
    tape and that's all there is to it make
  • 00:14:22
    sure you add tape to your scratch like
  • 00:14:23
    that and you'll see how helpful this is
  • 00:14:25
    going to be after we finish painting so
  • 00:14:27
    hopefully your scratch is tiny and you
  • 00:14:29
    just need to tape up a little area like
  • 00:14:30
    that but in this case we have a giant
  • 00:14:32
    scratch so
  • 00:14:34
    beautiful so now the entire scratch is
  • 00:14:36
    taped off top and bottom and this is
  • 00:14:38
    what it should look like and if you're
  • 00:14:39
    wondering don't worry about the tape
  • 00:14:41
    lines we'll have after the paint dries
  • 00:14:42
    we'll be sanding down the touch-up paint
  • 00:14:44
    so it's level with the surrounding paint
  • 00:14:45
    so paint lines don't even matter it's
  • 00:14:47
    just a lot less work if we keep the
  • 00:14:49
    paint contained to one small area so now
  • 00:14:51
    we are ready to go it is time to add our
  • 00:14:53
    paint to our scratch you want to make
  • 00:14:55
    sure you shake it up real good this
  • 00:14:57
    paint has primer and paint built in so
  • 00:14:59
    we don't need to prime it so let's
  • 00:15:00
    unscrew our brush and make sure you
  • 00:15:02
    remove all the excess paint by wiping
  • 00:15:04
    the brush on the edge of the container
  • 00:15:06
    so we don't have a big blob on the end
  • 00:15:07
    of the brush now when applying the paint
  • 00:15:09
    it's important we start with very thin
  • 00:15:11
    layers and apply to the top of the
  • 00:15:13
    scratch because gravity is going to pull
  • 00:15:14
    some of that paint down and as you can
  • 00:15:16
    see we have a paint drip coming down the
  • 00:15:18
    edge of our brush so let's wipe that off
  • 00:15:20
    so it doesn't add too much paint to the
  • 00:15:21
    scratch good and now we want to continue
  • 00:15:23
    to work our way from one end of the
  • 00:15:24
    scratch to the other making sure the
  • 00:15:26
    paint is being applied as thin as
  • 00:15:28
    possible while still getting coverage
  • 00:15:30
    like so now you might be tempted to go
  • 00:15:32
    back and try to touch something up but
  • 00:15:34
    don't do it don't go over here and try
  • 00:15:36
    to mess around with it because this
  • 00:15:37
    dries pretty quickly might dry in like
  • 00:15:40
    10-15 seconds and if you go back and try
  • 00:15:42
    to mess around with it that surface skin
  • 00:15:44
    that forms is gonna get messed up and
  • 00:15:46
    it's not gonna look good so just wait
  • 00:15:48
    don't worry we're gonna add some more
  • 00:15:49
    layers and it's gonna look way better
  • 00:15:51
    another thing is this paint is
  • 00:15:52
    relatively self-leveling so if you start
  • 00:15:54
    to go in there again you're gonna make
  • 00:15:56
    it look really rough but as it dries on
  • 00:15:58
    its own it'll self-level and be a lot
  • 00:16:01
    smoother than the texture that the brush
  • 00:16:02
    creates okay so five minutes later our
  • 00:16:05
    paint is ready for the next coat just
  • 00:16:07
    like before apply a thin coat on top of
  • 00:16:09
    the scratch and work your way across the
  • 00:16:11
    scratch and don't backtrack at all
  • 00:16:14
    five more minutes later we are ready for
  • 00:16:15
    our third coat and i think you get the
  • 00:16:17
    idea the whole goal is we want to build
  • 00:16:19
    up thin coats higher than the
  • 00:16:21
    surrounding paint that way when the
  • 00:16:22
    paint dries we could sand it down even
  • 00:16:24
    with the factory paint and also i'm sure
  • 00:16:26
    you've noticed you don't have to be good
  • 00:16:27
    at using a paint brush you just need to
  • 00:16:29
    make sure the layers are thin and even
  • 00:16:31
    and even if it doesn't look great it
  • 00:16:33
    will sand nice and smooth once we're
  • 00:16:34
    done another five minutes later and
  • 00:16:36
    we're on coat four and this coat is
  • 00:16:38
    gonna be a little bit thicker and we
  • 00:16:39
    don't want it to be a giant blob so you
  • 00:16:41
    could drag that paint across the rest of
  • 00:16:43
    the scratch to even it out just like
  • 00:16:45
    that and this scratch looks like it's
  • 00:16:46
    completely filled in so this is gonna be
  • 00:16:48
    our last layer so in this case it took
  • 00:16:50
    four layers for our paint to build up
  • 00:16:52
    thick enough so it's above the
  • 00:16:54
    surrounding paintwork we want it to be
  • 00:16:56
    above because now we're gonna sand it
  • 00:16:57
    down we're gonna sand it down so that
  • 00:16:58
    it's level with the rest of the paint so
  • 00:17:00
    don't worry if you add too many layers
  • 00:17:02
    in this case it took four it might take
  • 00:17:04
    you five it might take you six it could
  • 00:17:05
    take you three you just wanna make sure
  • 00:17:07
    you have more layers than you need you
  • 00:17:09
    wanna make sure it's thicker than the
  • 00:17:10
    surrounding paint that way when you sand
  • 00:17:11
    it down you could sand it even with the
  • 00:17:13
    rest of the body work so four layers
  • 00:17:15
    later and this paintwork is looking
  • 00:17:17
    absolutely
  • 00:17:18
    incredible our touch-up paint came out
  • 00:17:20
    awesome it matches really well you can
  • 00:17:22
    see how well it matches and i cannot
  • 00:17:24
    wait to take this tape off and finish up
  • 00:17:26
    this job and see how awesome it came out
  • 00:17:29
    now after letting the paint dry for
  • 00:17:31
    about 10 minutes we could carefully
  • 00:17:32
    remove the tape and don't just rip it
  • 00:17:34
    off do this slowly the trick is to pull
  • 00:17:36
    the tape back on itself as you're
  • 00:17:38
    removing it also pull the edge at a 45
  • 00:17:41
    degree angle away from the touch-up
  • 00:17:42
    paint that way it's going to give it a
  • 00:17:44
    nice sharp line without damaging the
  • 00:17:46
    paint so take your time and carefully
  • 00:17:48
    remove all the tape and any tape you
  • 00:17:50
    can't peel off use a straight edge to
  • 00:17:52
    lift the corner up so you don't damage
  • 00:17:53
    your touch-up paint with your finger and
  • 00:17:55
    once you get the corner up then it
  • 00:17:57
    should peel off nice and easy like that
  • 00:17:59
    all right and would you look at this
  • 00:18:01
    this is looking so much better already
  • 00:18:03
    now i know there are paint lines you can
  • 00:18:05
    clearly see it it's not blended in yet
  • 00:18:08
    but next step is to remove the paint
  • 00:18:10
    lines it's to sand this down so it
  • 00:18:12
    blends in with the rest of the paintwork
  • 00:18:14
    and it's gonna look incredible this
  • 00:18:16
    paint is matching super nice and you're
  • 00:18:19
    barely gonna be able to see this this is
  • 00:18:20
    gonna come out so good i'm so pumped
  • 00:18:22
    okay so let's get on to the next step
  • 00:18:24
    which is to sand down the touch-up paint
  • 00:18:26
    okay now for the sanding step we're
  • 00:18:27
    gonna be using 800 grit sandpaper so
  • 00:18:30
    what i like to do with the sandpaper is
  • 00:18:31
    i like to cut it into a small square
  • 00:18:33
    like that and with our sandpaper we
  • 00:18:36
    don't want to go and try to sand this by
  • 00:18:38
    hand that's gonna damage the clear coat
  • 00:18:39
    we're gonna get uneven marks what we
  • 00:18:41
    need is a small sanding block a typical
  • 00:18:43
    size sanding block is going to be way
  • 00:18:45
    too big for this little piece so find
  • 00:18:47
    something like a domino in this case the
  • 00:18:49
    domino works perfect it is a small flat
  • 00:18:51
    surface and what we're going to do is
  • 00:18:53
    wrap our sandpaper around the domino now
  • 00:18:55
    we have a flat small thin surface that
  • 00:18:58
    we could use to sand away the paint
  • 00:18:59
    lines without damaging the surrounding
  • 00:19:01
    clear coat now our touch-up paint is
  • 00:19:02
    completely dry it's been sitting here
  • 00:19:04
    for over an hour you don't want to sand
  • 00:19:06
    wet touch-up paint so let it dry and
  • 00:19:08
    hours plenty of time and now we just
  • 00:19:10
    need to sand these paint lines away and
  • 00:19:12
    you can see how the domino is just the
  • 00:19:13
    right width for sanding the touch-up
  • 00:19:15
    paint and the technique here is to sand
  • 00:19:17
    back and forth along the scratch until
  • 00:19:19
    it levels off with the surrounding
  • 00:19:20
    paintwork you want to do your best and
  • 00:19:22
    keep that sandpaper on the touch-up
  • 00:19:24
    paint and try not to sand the
  • 00:19:25
    surrounding factory paint too much and
  • 00:19:27
    once the scratch is level stop sanding
  • 00:19:30
    so you don't remove too much paint and
  • 00:19:31
    then run your finger across the scratch
  • 00:19:33
    and you shouldn't feel anything it
  • 00:19:35
    should feel nice and smooth like that
  • 00:19:37
    beautiful
  • 00:19:38
    now so you could appreciate what we just
  • 00:19:40
    did and the whole point of sanding it
  • 00:19:42
    down you can see our strong paint line
  • 00:19:44
    goes all the way across now right here
  • 00:19:46
    where we sanded it that section right
  • 00:19:47
    there this is completely gone it looks
  • 00:19:51
    perfect i mean it's not done yet we
  • 00:19:52
    didn't polish it yet we didn't add clear
  • 00:19:54
    coat and that scratch disappeared you
  • 00:19:56
    can't feel it at all and it looks
  • 00:19:59
    absolutely perfect that's exactly what
  • 00:20:01
    you want to do for the rest of your
  • 00:20:02
    scratch now since i'm working on a large
  • 00:20:05
    scratch to prevent the sandpaper from
  • 00:20:06
    gumming up with paint spray the area
  • 00:20:08
    down with soapy water and then you could
  • 00:20:10
    start sanding away and there really
  • 00:20:12
    isn't anything special to this all
  • 00:20:13
    you're doing is sanding the touch-up
  • 00:20:15
    paint so that it's level with the
  • 00:20:16
    surrounding paint so i'm going to work
  • 00:20:17
    my way around the entire scratch
  • 00:20:19
    leveling it out and just make sure you
  • 00:20:21
    keep that sandpaper localized onto the
  • 00:20:23
    touch of paint and then once the paint
  • 00:20:24
    is level with the surrounding area you
  • 00:20:26
    are done and when you think you're done
  • 00:20:29
    wipe your hand across the panel and see
  • 00:20:30
    if you can feel any bumps from the touch
  • 00:20:32
    of paint if you do feel bumps you didn't
  • 00:20:34
    sand enough keep going in this case this
  • 00:20:36
    feels nice and smooth now although this
  • 00:20:39
    looks great make sure you take your time
  • 00:20:41
    and visually inspect your entire scratch
  • 00:20:44
    if you see any spots where the paint
  • 00:20:45
    doesn't look great it's not up to your
  • 00:20:47
    standards you want to make it look
  • 00:20:49
    better now's the time to do it because
  • 00:20:51
    once you put that clear coat on it's a
  • 00:20:52
    lot more difficult to sand the clear
  • 00:20:54
    coat completely away and then retouch up
  • 00:20:56
    that area for example right here you can
  • 00:20:59
    see our scratch is pretty well blended
  • 00:21:01
    here you can't really see it but then
  • 00:21:02
    once you get right there there's an
  • 00:21:04
    indentation we either didn't put enough
  • 00:21:05
    paint in there or when we sanded it it
  • 00:21:07
    chipped away whatever the case is that
  • 00:21:09
    we will definitely see after we add our
  • 00:21:11
    clear coat so let's fix it and to fix it
  • 00:21:14
    all you need to do is fill it back in if
  • 00:21:16
    you want you could add tape i'm not
  • 00:21:17
    going to i'm going to just be extra
  • 00:21:19
    careful here and i just need to fill it
  • 00:21:21
    just a little bit so one coat should do
  • 00:21:23
    the trick and 10 minutes later let's get
  • 00:21:25
    some soapy water on there and wet sand
  • 00:21:27
    the touch of paint until it's nice and
  • 00:21:29
    level with the surrounding paintwork
  • 00:21:31
    good let's wipe it down and that looks
  • 00:21:34
    way better alright so once you're happy
  • 00:21:36
    with how your touch-up paint came out
  • 00:21:38
    the last thing we need to do is apply
  • 00:21:41
    our clear coat to all the parts that we
  • 00:21:43
    touched up but before we add clear coat
  • 00:21:45
    let's get some isopropyl alcohol on a
  • 00:21:47
    towel and wipe down the panel to remove
  • 00:21:49
    any dust that's still on there from
  • 00:21:51
    sanding now we can add our clear coat
  • 00:21:53
    and just like the color coat we want to
  • 00:21:55
    add thin layers start from one end of
  • 00:21:57
    the scratch and work your way down to
  • 00:21:59
    the other end and it's really difficult
  • 00:22:00
    to get clear coat to go on smooth
  • 00:22:02
    especially with a brush like this so
  • 00:22:04
    don't really worry about how it looks we
  • 00:22:06
    just want to have a complete layer
  • 00:22:07
    covering our touch-up paint and also a
  • 00:22:09
    little bit of overlap on the surrounding
  • 00:22:11
    factory paint and then after letting
  • 00:22:12
    this dry for 10 minutes apply one final
  • 00:22:15
    coat for a total of two coats again just
  • 00:22:17
    make sure the entire scratch is covered
  • 00:22:19
    in clear coat that way we could sand it
  • 00:22:20
    smooth with the surrounding clear coat
  • 00:22:22
    so with two thin layers of clear coat
  • 00:22:24
    coating our entire
  • 00:22:26
    scratch sealing in our touch-up paint
  • 00:22:28
    now i'm going to let this dry for about
  • 00:22:30
    an hour and an hour later you can see
  • 00:22:32
    the clear coat here is dry and has a
  • 00:22:34
    nice gloss to it but it's uneven and
  • 00:22:36
    there's ridges and stuff well to remove
  • 00:22:38
    the ridges spray it down with soapy
  • 00:22:40
    water and grab your 800 grit sandpaper
  • 00:22:42
    and start sanding it down so it's level
  • 00:22:43
    with the surrounding clear coat then we
  • 00:22:45
    can move up to 1 500 grit so spray down
  • 00:22:47
    the paint and wet sand the clear coat we
  • 00:22:49
    applied and start feathering out your
  • 00:22:51
    sanding into the surrounding clear coat
  • 00:22:53
    as well then we can move up the 2000
  • 00:22:55
    grit so spray down the paint and wet
  • 00:22:57
    sand our touch-up clear coat as well as
  • 00:22:59
    a little bit of the surrounding clear
  • 00:23:01
    coat and then let's wipe this down and
  • 00:23:02
    let's see how it came out and if you run
  • 00:23:04
    your finger across you can't feel the
  • 00:23:06
    clear coat it is nice and level with the
  • 00:23:08
    factory clear coat and that's exactly
  • 00:23:10
    what we want so at this point where you
  • 00:23:12
    added your clear coat should feel nice
  • 00:23:14
    and smooth we sanded it down so that
  • 00:23:16
    it's level with the factory paint work
  • 00:23:17
    and one way to make sure is close your
  • 00:23:20
    eyes and just run your fingers across
  • 00:23:22
    the panel you shouldn't be able to feel
  • 00:23:24
    any divots any valleys any hills any
  • 00:23:27
    bumps anything like that it should just
  • 00:23:28
    feel like one smooth panel and that does
  • 00:23:31
    that feels absolutely perfect so now you
  • 00:23:33
    can probably see there is a little bit
  • 00:23:35
    of a haze here and some of the panel's
  • 00:23:37
    glossy some of it's not glossy we need
  • 00:23:39
    to fix that and that's the fourth step
  • 00:23:40
    the final step that's where we do a wet
  • 00:23:42
    sand and then we polish it and we make
  • 00:23:44
    this look like one perfect panel so
  • 00:23:46
    let's get to it and to wet sand we're
  • 00:23:48
    going to start out with 3000 grit
  • 00:23:50
    sandpaper then we'll move our way up to
  • 00:23:52
    5000 grit sandpaper and finally to get
  • 00:23:55
    the gloss back we'll finish up with a
  • 00:23:56
    nice coat of polish now before you start
  • 00:23:59
    sanding a helpful trick i want to show
  • 00:24:00
    you don't use your bare hands to wet
  • 00:24:03
    sand what happens is your fingers create
  • 00:24:05
    pressure points on the sandpaper and you
  • 00:24:07
    won't get an even sand it'll create hot
  • 00:24:09
    spots and it won't look good so a trick
  • 00:24:11
    is to grab a sponge lay it over the
  • 00:24:13
    sandpaper wrap your sandpaper around it
  • 00:24:15
    and now the sponge will absorb any
  • 00:24:17
    pressure points so you have a nice even
  • 00:24:20
    sand now real quick i want to show you
  • 00:24:22
    up close what this is going to look like
  • 00:24:23
    so you can see where we've been working
  • 00:24:25
    right there it's all scratched up well
  • 00:24:27
    we're going to wet sand with the 3000
  • 00:24:29
    grit then we're going to wet sand with
  • 00:24:30
    the 5000 grit then we're gonna buff in
  • 00:24:32
    some polish which is a light abrasive
  • 00:24:35
    and then we'll buff that off and then
  • 00:24:36
    that will blend in that scratch you
  • 00:24:38
    can't even see it anymore it literally
  • 00:24:40
    disappears so we want to apply the same
  • 00:24:43
    process to the entire panel and make it
  • 00:24:45
    blend in and look uniform so spray it
  • 00:24:47
    down with soapy water and get some on
  • 00:24:49
    the sandpaper too and sand the entire
  • 00:24:51
    panel down with 3000 grit sandpaper and
  • 00:24:54
    while wet sanding make sure you move in
  • 00:24:56
    a back and forth motion don't do any
  • 00:24:58
    circles because circles form circular
  • 00:25:00
    scratches and circular scratches are
  • 00:25:02
    more difficult to remove than straight
  • 00:25:03
    scratches then you can wipe down the
  • 00:25:05
    panel to remove any small particles we
  • 00:25:07
    created with the 3000 grit sandpaper and
  • 00:25:09
    now we can spray the panel down with
  • 00:25:10
    soapy water and move on to our 5000 grit
  • 00:25:13
    sandpaper
  • 00:25:14
    again make sure you sand down the entire
  • 00:25:16
    panel don't miss any spots or you're
  • 00:25:18
    gonna see it when we're done finally do
  • 00:25:20
    one more wipe down and we are on the
  • 00:25:22
    last step which is the polishing step so
  • 00:25:24
    get some polish on the buffing pad and
  • 00:25:26
    then spread it out over the entire panel
  • 00:25:28
    and finally with heavy pressure buff the
  • 00:25:30
    polish into the panel in a circular
  • 00:25:32
    motion since polish is a very fine
  • 00:25:34
    abrasive the circular motion attacks the
  • 00:25:36
    scratches in all different directions to
  • 00:25:38
    make the clear coat nice and glossy so
  • 00:25:40
    now with the whole panel polished grab a
  • 00:25:42
    fresh microfiber towel and buff off the
  • 00:25:44
    polish to reveal a nice and shiny panel
  • 00:25:47
    look at that and beautiful we brought
  • 00:25:50
    back all that gloss to our panel and
  • 00:25:53
    this is a real high gloss shine right
  • 00:25:54
    now and we blend it in the scratch so
  • 00:25:56
    you can't even see it and with that we
  • 00:25:59
    are done and holy smokes you can't even
  • 00:26:01
    see the scratch anymore it is gone look
  • 00:26:04
    at that and just as a reminder this is
  • 00:26:06
    what the scratch looked like before we
  • 00:26:08
    started it's clearly visible doesn't
  • 00:26:10
    look good at all and here's what it
  • 00:26:12
    looks like after you can't even see it
  • 00:26:14
    you would never know there was a giant
  • 00:26:15
    deep scratch on here now although these
  • 00:26:17
    results are absolutely amazing it's not
  • 00:26:20
    perfect you can still see the scratch if
  • 00:26:22
    you get to the right angle and you could
  • 00:26:24
    kind of kind of see it right there it's
  • 00:26:27
    a little tough to see but you get the
  • 00:26:29
    idea if you get to the right angle if
  • 00:26:30
    you get up close you're able to see it
  • 00:26:32
    once you step back just a little bit it
  • 00:26:34
    disappears it's gone and then if you're
  • 00:26:36
    looking at the car from 5-10 feet away
  • 00:26:38
    you'll never see it so for 15 a paint
  • 00:26:41
    pen works so well and now you know how
  • 00:26:43
    to get these kind of results so with
  • 00:26:45
    your panel all touched up it's looking
  • 00:26:47
    beautiful you might be tempted to try to
  • 00:26:48
    add a wax or ceramic coating to protect
  • 00:26:51
    it but don't do that just yet touch-up
  • 00:26:54
    paint can take up to 30 days to fully
  • 00:26:56
    cure and harden so you don't want to
  • 00:26:58
    seal it off and prevent that from
  • 00:26:59
    happening in the meantime you could
  • 00:27:00
    still drive the car you could still get
  • 00:27:02
    it wet go in the rain wash the car
  • 00:27:04
    whatever just don't seal it with a
  • 00:27:06
    ceramic coating or a wax so there you go
  • 00:27:09
    now you know how to properly repair deep
  • 00:27:11
    scratches using a simple touch-up pen
  • 00:27:13
    and this came out absolutely amazing it
  • 00:27:16
    looks incredible and you guys could get
  • 00:27:19
    those same results also another thing i
  • 00:27:21
    want to mention is if you get little
  • 00:27:23
    rock chips on your front bumper from
  • 00:27:24
    rocks kicking up you can follow the same
  • 00:27:26
    exact steps and get the same amazing
  • 00:27:28
    results so hopefully the video was
  • 00:27:30
    helpful if it was remember to give it a
  • 00:27:31
    thumbs up if you're not a subscriber
  • 00:27:33
    consider hitting that subscribe button
  • 00:27:34
    for more automotive how-to videos just
  • 00:27:36
    like this and as always all the tools
  • 00:27:38
    and products i used in this video are
  • 00:27:40
    linked in the description
Tags
  • réparation de voiture
  • rayure profonde
  • peinture automobile
  • stylo de retouche
  • DIY
  • Chris Fix
  • entretien automobile
  • réparation de peinture
  • tutoriel
  • carrosserie